moreno0101

Kelvin kdx, polk db6501 had the right rms I was looking for, I had to use the supplied spacers but it installed with.no problem. The tweeters fit in the tweeter hole behind that grille and snapped into place. Sounds sweet.... I put a pair in the front and back

Kelvin kdx, polk db6501 had the right rms I was looking for, I had to use the supplied spacers but it installed with.no problem. The tweeters fit in the tweeter hole behind that grille and snapped into place. Sounds sweet.... I put a pair in the front and back

@Ssg-John L Dodson III - if your trying to add touch screen navi to your SE, clarion still makes a single DIN motorized head unit.

@evilballa Nevermind...i just read your manual... Anthony Masotti might know, he is the guy who posted a build he did with that product. Good Luck.

Thanks Guys, I finally got my system to where I want it. The dash was a little tricky only because those clips at the top where stronger than I thought. I used a trim pry tool (a plastic crow bar). I really want to run new speaker wire to my doors, but getting through that little S shaped sleeve between the door seems like a pain. @evilballa I used a different product (audiocontrol LC7i) it has an auto on function when it senses a signal from the stereo. I'm not sure about the clean sweep, but for the price of it...I'm sure it has a similar feature, you might not need to use the remote input.

Im doing my install today and the factory stereo (8" lcd non touch screen) wont come out after taking the bottom two bolts off. Anyone know what im missing?

Im doing my install today and the factory stereo (8" lcd non touch screen) wont come out after taking the bottom two bolts off. Anyone know what im missing?

Im doing my install today and the factory stereo (8" lcd non touch screen) wont come out after taking the bottom two bolts off. Anyone know what im missing?

@Anthony and anyone else here that might know. I looked at the wire diagram and from what it looks like there is no factory Amp, i guess its built into the head unit. I see the amp enable line is not used. also, where did you find the ignition relay that you hooked your remote wire too? I had some hack install my gear and he jacked it all up. The amps turn on like you said they would :doh:when you open the door and there is white noise at really low volume,........and they used cheap speaker wire....I'm redoing the whole thing myself to save me more trouble and making sure its done right. thanks to all your info I think i will do a better job than those jerks at the shop. Question: would you guys run new wire to the doors or use the factory speaker wires? Thanks guys, Rafael

Oh man, so I got the audio control LC7i installed with Polk Audio DB6501 in the front and back doors, and an 8" kicker solo baric in the trunk. i think the components are drowning out the little 8" sub, but it still sounds 1000X better than the stock set up. have RMS matched 450 RMS amp for the Sub another amp that gives 95x4 for my mids which are rated at 100x4. It really sounds sharp. you cant tell where the sound comes from, its just overwhelms you. Thanks for all your help guys, Next step is to install some sound dampening material, it didnt arrive in time to the install, but I knock it out on my day off. surprisingly there isnt much rattle coming from the doors or trunk.

@anthony you come through again. Thanks. Save me some time and money. Much appreciated. Have a good one.

@Botts I just read up on the manual for the LC7i, thanks for the heads up. @Anthony I know this is a long shot, but do you have the instruction for removing the side panels and carpeting from the rear deck? Or I'm I just being too cautious? looks like a bunch of plastic clips holding the carpeting in, but I have to remove some of the side plastics to get at it. I'm installing an amp rack under the rear deck today, and I need to feed some bolts to attach some support beams for the shelf. any info would be great. Have a good one guys. Thanks for the input. Rafael

@anthony thanks again for the info. I went to my local dealership service dept and they didnt want to give the the wireing diagram. Said I would mess things up, and he wouldn't recommend it. I couldn't believe it. Im going to have this professionally done, I just like to know what the hell im talking about when I speak with the installer. Thanks again.

@anthony thanks again for the info. I went to my local dealership service dept and they didnt want to give the the wireing diagram. Said I would mess things up, and he wouldn't recommend it. I couldn't believe it. Im going to have this professionally done, I just like to know what the hell im talking about when I speak with the installer. Thanks again.

@anthony im using a audio control Lc7i, it was a lot cheaper and hopefully does a good job of summing up the signal for the amps. The clean sweep was a bit too expensive. Hopefully it does the job. Well see.

@anthony thanks for the great info. The best info I have found online so far. Your awesome. Noe for a lame question... is the amp enable wire on your diagram the same as a remote wire?